6.3. Simulated performance of the BLDC motor drive with the Cuk converter operating in the DICM (Lo ). Fig.5.3 shows the performance of the proposed BLDC motor drive fed by a PFC Cuk converter operating in the DICM (Lo
2. Momin Muhammad Zia Muhammad Idris “ Optimization of crankshaft using strength analysis”, International Journal of Engineering Reasearch and applications, Vol-3, Issue-3, ISSN:2248- 9622, Pages: 252-258, MayJun-2013. 3.Abhishek choubey, Jamin Brahmbhatt, “Design and Analysis of Crankshaft for single cylinder 4-stroke engine”, International Journal of Advanced Engineering Reaserch and studies, vol-1, issue-4, ISSN:2249-8974, pages: 88-90, July-sept 2012. Table 1 Comparison between Forged steel and Ti-6Al-4V+12% TIC using ANSYS Material Forged steel Ti-6Al-4V+12% TIC MIN MAX Min Max Total deformation (m) 0 7.749E-6 0 1.54E-8 Equivalent Elastic Strain(m/m) 2.38E-12 0.0006146 1.05E-14 1.18E-6 Equivalent stress (Pa) 0.4561 1.1E8 1.02 1.09E8 Life(cycles) 394.74 1E6 364.82 1E6 Damage 1000 3.753E7 1000 3.68E7 Page 6 of 7 Page 7 of 7 4. BDNS Murthy “ Modeling analysis and optimization of crankshaft”, vol-2, Issue- 9, ISSN: 2278-0181, Pages: 749-753, September-2013.
The customer’s demand is expressed as a function of time, price and credit period which is appropriate for the products for which demand increases initially and after sometime it starts to decrease. In order to reduce the holding cost of supplier, the production is considered as one of the decision variable, which is directly proportional to the customer’s demand rate. The aim of this paper is to maximize the joint profit for supplier and retailer. Some numerical examples are demonstrated for validation of the developed mathematical model. Finally, implementing sensitivity analysis on the decision variables by varying the inventory parameters, effective managerial insight are generated which is beneficial for players of supply chain.
After developing a pricing strategy, then begins the process of marketing of the product. They are both vital in topping up the sales. It is also important to identify what kind of product to sell in order to determine the type of business. The first type of business is volume driven where prices can be manipulated up and down. Questions are asked whether
Production planning and control functions of JIT and TOC system helped Adamas to reduce wastage, work on the bottlenecks to improve the overall profits. In this chapter 1.2, let us discuss about the production planning and control functions and their role in the production processes. 1.2.1 Production Planning Production planning answers the questions related to production such as what to, how much and when to produce. In the words of Jay wild, “Production planning is concerned with the determination, acquisition and arrangement of all facilities necessary for future operations.” Major purpose of production planning is utilising the available resources in an efficient
A. Introduction Crankshaft is one of the significant components of an engine which has a four bar link mechanism. The crankshaft is prominent in size and complicated in geometrical structure and it is used to transubstantiate from reciprocating motion into rotary motion. It induces the engine to rotate. Main bearing is rotated along with the shaft parts
Business and System Analysts have to follow these processes so as to do their job efficiently 1 Conception Business Analyst needs to first understand the project history or a problem and the existing systems to have a reasonably clear picture of the current state that needs to change. A detailed investigation of the system is made by the analyst and then make a proposal which list the problem definition, objectives, constraints, expected benefits of a new system ,etc. Cost benefit analysis,, risk management plan and feasibility study is done in this stage by the analyst. 2 Analysis Analysis involves identification of the business problem and opportunities, and assessment and validation of potential and actual
An appropriate balance between capacity and demand can satisfied the customers and eventually lead to organization profits. Capacity planning is the process of determining the production capacity to meet changing demands for its products. Capacity planning and control is the task of setting up the capacity of operations so that it responds to demand placed upon it. This means that taking a decision how the operations should react to demand fluctuations. Capacity planning and control is major responsibility of operation managers.
Second main topic is about engineering mechanics of human motion analysis. In this topic, the human body’s motion were describes and relates referring on the kinetics, kinematics, dynamics, and biomechanics analysis. Another sub
Ideally, then a seller might design a separate marketing program for each buyer. Targeting: Targeting the market is a phase which comes simultaneously after segmentation of market. Once the market is divided, the organization becomes aware of the audience they 've to deal with in respect to their age, gender, occupation, location, etc. And thus, they can plan ahead of the marketing activities that are to be implemented and executed which is also known as Positioning. (1)Gordon Wyner, (2002) vice president of Mercer Management Consulting, writes that effective segmentation enables companies to allocate investment resources towards targeted customers that are most likely to be attracted to offers.