In our current time different techniques are used to analyse and improve the properties of different elements and materials in order to improve day to day uses that will help better the environment and the quality of life or to improve the economy. One of these techniques is thermo gravimetric analysis this analytical technique measures the rate of change in mass of a material as a function of time or temperature in a controlled environment, the measurements can be used to determine the composition of the material and its thermal properties as the endothermic and exothermic reactions occur when the material is heated therefore determining the mass loss or gain of the material due to oxidation, decomposition or dehydration.
As the discovery
…show more content…
Different materials such as automotive parts, rubber, plastic, glass and vinyl fabrics can be analysed using thermal gravimetric analysis, the sample requirements for this technique are that the sample has to either be a liquid or a dry solid, should not burn explosively or react with the sample holder, most of the samples that are analysed are polymers which are typically between the 10-20mg, metals and inorganic material which is mainly between the 40-50mg …show more content…
A high resolution thermal gravimetric analysis method is usually used as it has great accuracy this is because as the weigh of the sample increases the temperature is increase is slowed so that the exact temperature at which the weight is the highest can be accurately
Cadet Eric Wiggins Date: 18 September 2014 Course Name: Chem 100 Instructor: Captain Zuniga Section: M3A Identification of a Copper Mineral Intro Minerals are elements or compounds that are created in the Earth by geological processes. The method of isolating metals in a compound mineral is normally conducted through two processes.
In the first part of the experiment, Part A, the standard solutions were prepared. As a whole, the experiment was conducted by four people, however, for Part A, the group was split in two to prepare the two different solutions. Calibrations curves were created for the standard solutions of both Red 40 and Blue 1. Each solution was treated with a serial 2-fold dilution to gain different concentrations of each solution.
After the water temperature began to stabilize, the highest constant temperature was recorded. This data was used to calculate the calorimeter constant. This enter procedure was repeated to calculate another calorimeter constant in order to find the average of both answers. After that value was calculated, a 600 mL beaker was filled with 300 mL of water and heated till it started boiling. An unknown metal located on the instructor's bench was obtained and the mass was calculated.
section{Evaluation} label{sec-analyze} vspace{-0.08in} We evaluate Tarax with the six popular server applications described above. We first perform experiments to compare the performance and code sizes of the Tarax-optimized kernels and the vanilla kernel. We then perform dynamic profiling on the kernels to collect detailed statistics on instruction cache misses and branches. Finally, we switch on specific GCC optimizations with and without profile feedback, respectively, to collect performance numbers.
The Controlled Variable for this experiment was mass and volume. When identifying an unidentified object finding the density is the easiest way to do it because, any pure substance has a specific density at a specific temperature and each element and compound has a unique density associated
To begin with, is the experimental process used to determine the identity of the rock. In doing so one will need to discover the density of the rock. By measuring the rock sample with grams per milliliter is a way used to figure out the density. In starting one will need to measure the mass of the rock using grams. Then using a set milliliter amount of a liquid substance, such as water, one will place the rock sample inside.
Pedophile in Penn State The general argument made by Maia Szalavitz in her work, “Bystander Psychology: Why Some Witnesses to Crime Do Nothing”, is that it is wrong when people view crime, and they do not take action. More specifically, Szalavitz argues that people tend to keep quiet for each other as a conglomerate. She writes, ”Mike Mcqueary… witnessed child rape firsthand in 2002...
Method A) Prepare a NaOH solution (approximately 0,1M NaOH) 1. Place a clean, dry glass beaker on the electronic scale. 2. Determine the mass of the glass beaker. 3.
75.33 grams Weight of the unknown = 0.23 grams Calculation : 75.33-75.10/0.36x100 = 63.8 % recovery Melting point of
The observed emission data for the different elements did not look how they were supposed to. However the “peaks” for Hydrogen were found to be 534.52 and 631.24, 534.70 and 569.11 for Helium and 529.73 and 630.71 for Mercury. The Rydberg’s Constant found to 1.1x107 8.5x104 while the known constant is 10967758.34m-1. The percent error of 0.29% and the accuracy of this reading is 99.7. The slope and intercept of the linear regression line is -0.01 3.3x10-5 and 0.02x10-1 1.9x10-6 respectfully.
3. To purify and identify the product, recrystallization is used in order to purify the product, then melting point and TLC techniques are used to identify the product. Theory 4.
We found that gravity filtration is more suitable for the recovery of a solid material. The capillary tube with a lesser amount of compound melted at a higher temperature than the capillary tube with more compound, as well as having a smaller melting point range. This is because the larger sample size, took longer for the heat to disperse and therefore had a large melting point range.
F. How close was your calculation of the value of g at your location? What might be a few sources for error in your experimental data and calculations? All of my calculations were close to the accepted value of gravity. A few of my calculations were further off, but most were very close.
Forces and Newton II Elias Ghantous PHYS 151 – Section NQ Thursday 10:10am Hasbrouck Lab Room 214 October 13, 2017 Abstract In this experiment, I studied how forces cause an object to accelerate. I also studied the relationship between force vectors, mass and acceleration. Gathering of data took place through the use of a force table and a PAScar track system.
Calorimeter helped many generations to measure the quantity of heat using different types of devices; also they followed a specific procedure and equations to find out quantitative